What Is Test Mode On Motion Sensor Lights?

What are the settings on a motion sensor light?

If set for the “1” setting, the lights will come on for 1 minute after detecting motion, and then will go off and return to the AUTO motion sensor mode.

When set for “5”, the lights will remain on for 5 minutes after detecting motion.

If set for “10”, the lights will remain on for 10 minutes after detecting motion..

How do you adjust a motion sensor light?

Move the LUX stetting to day mode being the sun picture and put the time on the minimum setting.Switch the light switch on that controls the sensor.Move the sensor to the direction you what it to scan.Walk test. … Adjusting if needed some sensors can move up and down a side to side to help get the best angle.More items…

Why does my motion sensor light come on during the day?

The light comes on during the day. The “ON-TIME” switch is in the test position to allow light fixture operate during the day. … Heat or light from the lamp heads may be turning the motion sensor on and off.

How do you reset a motion sensor light?

Step 2: Turn your light switch on and off quickly, hitting each position four times. When the light comes on, turn the switch to the off position and wait five to seven seconds before turning it on again. The light should remain off and the motion detection unit should be reset.

Can you cover a motion sensor?

A quick solution that customers have said works well is to use black electrical tape to cover part of the sensor. Start by covering the edge of the sensor on the side you want to keep out of the detection area and use small pieces of tape to block it out.

Can you turn off motion sensor lights?

Disabling Motion Sensor Lights A switch on the fixture should read “on time,” usually found directly under the motion sensor. Set it to any position, aside from the test position, and flip off the switch that the light is connected to. … Once the flip is off, switch it back on immediately.

How long do motion lights stay on?

20 minutesOn average, a motion detector light will stay on for up to 20 minutes. That amount of time is extended each time a sensor detects fresh movement, so it is possible for a motion detector light to stay on for much longer than 20 minutes at a time.

Do motion sensor lights only work at night?

Motion sensors are a common form of outdoor lighting, but they don’t keep the yard lit all night long. Instead, they’re used in situations where you only need light when someone’s nearby. You can install them in backyards to let pets out at night or as theft deterrents around your home’s exterior.

Can motion sensor lights be set to stay on?

Most motion detectors have a built-in override: Normally the switch is kept on all the time. … If you turn the switch off and on within a second or so, the light will stay on, and this overrides motion detection. To go back to normal operation, turn the switch off and wait ~10 seconds, then turn back on.

Why is my motion sensor light not working?

If the light won’t come on after adjusting and cleaning the sensor, try a simple trick. Turn off the circuit breaker that controls the light circuit and leave it off for 30 minutes. … If the light doesn’t come on when you turn the breaker back on, try replacing the bulb. If that doesn’t work, the sensor may be bad.

How do you adjust a motion sensor?

Locate the switch, usually located on the bottom of the motion detector, and set it to the “TEST” position. The motion detector will also have an adjustment for sensitivity. This may be set with a screwdriver or small knob. Locate the sensitivity adjustment and set it for a “MEDIUM” level.

Why does my motion sensor light stay on all the time?

What Causes my Light to Stay On? Several things can cause your motion detector to stay on, including age, storm damage, a power surge, improper installation, and improper settings. A few issues are easy to correct without professional help.

How do you fix a light sensor?

How Can You Fix Motion Sensor Lights?Try Cleaning the Photocell. The photocell is an important part of the motion sensor light. … Turn It Off and Back On. Believe it or not, sometimes all your motion sensor lights need is to be manually switched off and on again! … Replace the Batteries. … Replace the Bulb.